Description
The TileMaster 40 Intro Starter Kit gives you the four TileMaster floor cleaners and all three TileMaster 40 machine pads in one box, so you can clean, lift grout haze and strip old sealers on the surfaces each cleaner is made for. The 1 litre bottles are concentrates. The TileMaster 40 machine is sold separately. Free UK mainland delivery.
What’s in the box
- Cleaner No.1 Ceramic & Porcelain Tile Cleaner, 1 litre concentrate
- Cleaner No.2 Natural Stone Tile Cleaner, 1 litre concentrate
- Cleaner No.3 Heavy Duty Extreme, 1 litre concentrate
- Cleaner No.4 Grout & Builders Dust Residue Remover, 1 litre concentrate
- Pad A: tile and grout cleaning pad, 20 cm × 40 cm
- Pad B: grout haze removal pad
- Pad C: thin burgundy stripping pad
The TileMaster 40 machine is not included.
Which cleaner
Choose the cleaner for your surface and job, not for the pad. Cleaner No.1, 2, 3 or 4 can each be used with any of the three pads, as long as the cleaner suits the surface.
- Cleaner No.1: everyday and deep cleaning of ceramic, porcelain, vinyl and LVT. A pH-neutral cleaner with a built-in degreaser. Not for natural stone or wood (use No.2 on natural stone).
- Cleaner No.2: everyday and deep cleaning of natural stone, including marble, travertine, limestone, slate, granite and sandstone. A pH-neutral cleaner with no acids, alkalis or bleaches. Not for wood or vinyl.
- Cleaner No.3: heavy built-up dirt and grease on porcelain, ceramic and unpolished natural stone, and grout haze on honed stone. A high-strength alkaline cleaner. Not for wood, vinyl, or polished or shiny natural stone.
- Cleaner No.4: grout haze, cement, plaster and builders’ dust on ceramic, porcelain and acid-resistant stone only. A concentrated acid cleaner. Never use on marble, limestone, travertine, or other acid-sensitive or polished surfaces. If you are unsure whether your stone is acid-resistant, test a small hidden area first or contact us before use.
Which pad when
- Pad A: everyday deep cleaning of ceramic, porcelain, natural stone, quarry, terracotta, vinyl/LVT, concrete, safety floor and slate.
- Pad B: removes grout haze, plaster and builder dirt after installation.
- Pad C: removes old floor sealers and acrylic finishes without harsh chemical strippers.
How to use
- Pick the cleaner and the pad using the lists above. Any of the four cleaners can be used with any of the three pads, as long as the cleaner suits the surface.
- Test a small area first. Try it somewhere hidden before doing the whole floor.
- Dilute the cleaner. These 1 litre bottles are concentrates. For a deep clean, mix 1 part cleaner to 4 parts water (100 ml cleaner to 400 ml water). Apply and leave for 5 minutes, keeping it wet so it does not dry on the floor.
- Fit the pad. Secure the pad to the base of the TileMaster 40 machine.
- Run the machine. Move it smoothly over tiles and grout. Let the machine do the work.
- Wipe and rinse. Remove the dirty solution with a mop or cloth, then rinse well with clean water. Rinse the pad after use and store it dry.
For rust marks on porcelain, the Cleaner No.4 page says to use the 1 litre concentrate neat (not a pre-diluted mix), leave for 15 minutes keeping the area wet, then scrub and rinse. Always test first. Coverage and other dilutions are on each cleaner’s own page (for example No.1 and No.2 also have weaker mixes for everyday mopping).
Safety
Read the TileMaster 40 machine instructions first, and read each cleaner’s label and Safety Data Sheet before use. Wear protective gloves and eye protection, and keep the room ventilated. Test a small area first. Keep children and pets away while you work, and store the products out of their reach.
- Cleaner No.1 and No.2: not classified as hazardous under CLP on their live pages. They can irritate the eyes. Wear gloves and eye protection.
- Cleaner No.3: a corrosive alkaline cleaner (live page: signal word Danger, causes severe skin burns and eye damage, pH 12.5). Store locked up. If it gets in the eyes, rinse cautiously with water for several minutes and remove contact lenses if easy to do.
- Cleaner No.4: a corrosive acid cleaner containing orthophosphoric acid (live page: signal word Danger, causes severe skin burns and eye damage, pH 2). Never use it on marble, limestone, travertine or other acid-sensitive stone. Store locked up. If it gets in the eyes, rinse cautiously with water for several minutes and remove contact lenses if easy to do.
Do not mix the cleaners. Use one at a time. Always read each product’s label and safety data sheet.
Need help? WhatsApp 07949 908666


























What others are saying
There are no contributions yet.